NAS

Pogoplug is cheap $20 and as good as or better than other NAS. I hook up my Pogoplug classic E02 and a free USB drive (4GB) from Microcenter.

Basic statistic about Pogoplug E02

See http://archlinuxarm.org/platforms/armv5/pogoplug-v2-pinkgray for hardware specification.

• architecture: ARMv5te
• Processor: Marvell Kirkwood 1.2GHz
• RAM: 256MB
• 124MB NAND
• Gigabit ethernet
• 5W power
• 4 USB 2.0 connector.

Install ArchLinux on pogoplug (Debian is better actually)

See the instruction in http://archlinuxarm.org/platforms/armv5/pogoplug-v2-pinkgray for how to install Archlinux on pogoplug (E02). I make a copy below.

killall hbwd
cd /tmp
wget http://jeff.doozan.com/debian/uboot/install_uboot_mtd0.sh
chmod +x install_uboot_mtd0.sh
./install_uboot_mtd0.sh
/sbin/fdisk /dev/sda

At the fdisk prompt, delete old partitions and create a new one:

• Type o. This will clear out any partitions on the drive.
• Type p to list partitions. There should be no partitions left.
• Now type n, then p for primary, 1 for the first partition on the drive, and then press ENTER, accepting default values.
• Exit by typing w.

wget http://archlinuxarm.org/os/pogoplug/mke2fs
chmod 755 mke2fs
./mke2fs /dev/sda1
mkdir usb
mount /dev/sda1 usb
cd usb
wget http://archlinuxarm.org/os/ArchLinuxARM-armv5te-latest.tar.gz
tar -xzvf ArchLinuxARM-armv5te-*.tar.gz  # This will take a long time
rm ArchLinuxARM-armv5te-*.tar.gz
sync  # Takes a while when using a flash drive. Not in my case however.
cd ..
umount usb
/sbin/reboot

Log back in after your Pogoplug reboots using username root and password root.

At the end, the system is very lean.

[root@alarm ~]# free
             total       used       free     shared    buffers     cached
Mem:        252492      28292     224200          0       4580      14072
-/+ buffers/cache:       9640     242852
Swap:            0          0          0
[root@alarm ~]# df -lh
Filesystem      Size  Used Avail Use% Mounted on
rootfs          7.4G  443M  6.6G   7% /
/dev/root       7.4G  443M  6.6G   7% /
devtmpfs        124M     0  124M   0% /dev
run             124M  224K  124M   1% /run
shm             124M     0  124M   0% /dev/shm
tmpfs           124M     0  124M   0% /tmp
[root@alarm ~]# uname -a
Linux alarm 3.1.10-13-ARCH #1 PREEMPT Mon Aug 20 15:46:18 UTC 2012 armv5tel GNU/Linux
[root@alarm ~]# cat /proc/cpuinfo
Processor	: Feroceon 88FR131 rev 1 (v5l)
BogoMIPS	: 1191.11
Features	: swp half thumb fastmult edsp 
CPU implementer	: 0x56
CPU architecture: 5TE
CPU variant	: 0x2
CPU part	: 0x131
CPU revision	: 1

Hardware	: Marvell SheevaPlug Reference Board
Revision	: 0000
Serial		: 0000000000000000
[root@alarm ~]# cat /proc/cpuinfo
Processor	: Feroceon 88FR131 rev 1 (v5l)
BogoMIPS	: 1191.11
Features	: swp half thumb fastmult edsp 
CPU implementer	: 0x56
CPU architecture: 5TE
CPU variant	: 0x2
CPU part	: 0x131
CPU revision	: 1

Hardware	: Marvell SheevaPlug Reference Board
Revision	: 0000
Serial		: 0000000000000000
[root@alarm ~]# 

After it, follow the instruction on lifehacker and https://wiki.archlinux.org/index.php/DeveloperWiki:usrlib

pacman -Syu --ignore glibc
pacman -Su
mkinitcpio -p linux

To install rsync, use

pacman -S rsync

Unfortunately, I cannot bypass the error

[root@alarm ~]# pacman -Suy rsync
:: Synchronizing package databases...
 core is up to date
 extra is up to date
 community is up to date
 alarm is up to date
 aur is up to date
:: Starting full system upgrade...
resolving dependencies...
looking for inter-conflicts...

Targets (2): glibc-2.16.0-4  rsync-3.0.9-5

Total Installed Size:   34.26 MiB
Net Upgrade Size:       0.61 MiB

Proceed with installation? [Y/n] 
(2/2) checking package integrity                        [#############################] 100%
(2/2) loading package files                             [#############################] 100%
(2/2) checking for file conflicts                       [#############################] 100%
error: failed to commit transaction (conflicting files)
glibc: /lib exists in filesystem
Errors occurred, no packages were upgraded.

Install Debian on pogoplug

See the instruction on http://projects.doozan.com/debian.

• Find your devices's IP address and connect via SSH:
• Partition your flash drive with fdisk (or gparted):

fdisk /dev/sda
# Configure partion 1 as Linux (I'd recommend making this at least 512Mb. The default bare-bones installation uses 280Mb.)
# Configure partion 2 as Linux Swap (I used 256MB.  Adjust according to your anticipated memory usage.)
# Set partition 1 active

See http://www.terminally-incoherent.com/blog/2012/09/19/set-up-a-home-linux-server-for-30-with-pogoplug/ for clear explanation of using fdisk.

• Download and run the Debian Wheezy installer:

cd /tmp
wget http://projects.doozan.com/debian/kirkwood.debian-wheezy.sh
chmod +x kirkwood.debian-wheezy.sh
export PATH=$PATH:/usr/sbin:/sbin
./kirkwood.debian-wheezy.sh

• Alternatively, you can choose to install Debian Squeeze with the following commands:

cd /tmp
wget http://projects.doozan.com/debian/dockstar.debian-squeeze.sh
chmod +x dockstar.debian-squeeze.sh
export PATH=$PATH:/usr/sbin:/sbin
./dockstar.debian-squeeze.sh

The script will take some time to download the debian images and extract them to your flash drive. The total install time will vary with the speed of your flash drive and your Internet connection. On my system, it takes about 20 minutes. Once it's finished, you can reboot into your new Debian install.

After your device reboots, it may have a different IP address (it's identifying as 'Debian' to the DHCP server now instead of 'Pogoplug').

The default root password in Debian is 'root'. After you've logged in, you should change the root password and configure /etc/apt/sources.list to point to a Debian mirror near you.

passwd
nano /etc/apt/sources.list

After reboot, the debian system is very lean too

root@debian:~# df -h
Filesystem            Size  Used Avail Use% Mounted on
rootfs                3.2G  260M  2.8G   9% /
none                  123M   36K  123M   1% /dev
/dev/sda1             3.2G  260M  2.8G   9% /
tmpfs                 125M     0  125M   0% /lib/init/rw
tmpfs                 125M     0  125M   0% /dev/shm
tmpfs                 125M     0  125M   0% /tmp
root@debian:~# free
             total       used       free     shared    buffers     cached
Mem:        255672      19636     236036          0        816      11104
-/+ buffers/cache:       7716     247956
Swap:       535544          0     535544

After I install LAMP, the memory uses 250MB. However, after I reboot the pogoplug, it reduces to 66MB.

root@debian:~# free
             total       used       free     shared    buffers     cached
Mem:        255672      66076     189596          0       1244      37000
-/+ buffers/cache:      27832     227840
Swap:       535544          0     535544

If I want to add a USB drive, it is safe NOT to insert the 2nd USB drive when the system boot. It is better to insert the 2nd USB drive after the system has booted. In my experience, if I insert the 2nd USB drive when the system boot, the first USB drive will be mounted as /dev/sdb1 but I want the 2nd USB drive mounted as /dev/sdb1.

Install build-essential. Should be fine. See Home automation link below.

Other resources:

• http://wiki.daviddarts.com/Pogoplug
• http://fzr.squeenus.com/debian/
• http://www.terminally-incoherent.com/blog/2012/09/19/set-up-a-home-linux-server-for-30-with-pogoplug/
• http://planetgary.blogspot.com/2011/08/home-automation-on-debian-powered.html Home automation
• http://bastel.dyndns.info/~dockstar/debian/ install some essential tools
• http://www.debian.org/ports/arm/ ARM port on debian

Make it more powerful

• Backup server (RAID 1). Crash plan.
• Remote file access (AjaXplorer).
• Cloud. (OpenStack)
• BitTorrentTM client
  • http://archlinuxarm.org/support/guides/applications/transmission
  • http://aaronrandall.com/blog/installing-a-bittorrent-client-on-the-pogoplug/ and here.
  • From transmission wiki specific to Debian. How to edit configuration file.

apt-get install transmission-cli transmission-common transmission-daemon
nano /etc/transmission-daemon/settings.json
# change “download-dir”, “incomplete-dir”
# change rpc-whitelist to "*" or your remote IP
# change "rpc-username" ,
#        "rpc-password"  (this will then be hashed, so don't worry)
# change "speed-limit-up": 10,
#        "speed-limit-up-enabled": true,
# change upload-limit (KB/s) from 100 to 10
#        upload-limit-enabled from 0 to 1
mkdir /mnt/usb/Downloads
chmod -R 777 /mnt/usb/Downloads
transmission-daemon 

/etc/init.d/transmission-daemon stop

# Remember to shut down transmission before editing the settings.json file

/etc/init.d/transmission-daemon start

Open browser http://hostname:9091/transmission/web

For pirat*, we can download torr* by using (see here)

http://torrents.thepiratebay.se/xxxxxx/My.torrent

So we don't need to download the torrent in our local machine. In fact, we can just right click 'Get this torrent' button and copy the link. Then we can open the url in transmission/web.

Note: the transfer speed from pogoplug to ubuntu is about 5.5MB/s.

• SFTP server. Cyberduck.
• WebDAV, owncloud.org.
• SAMBA server. So every computer in LAN can access the contents there. On Windows computer, type \\192.168.1.3\ShareFolder, for example.
• UPnP media server will stream the media content on your Pogoplug to any compatible media player such as the PlayStation 3, Microsoft Xbox 360, and D-Link Boxee Box over your local network.
• Email alerts
• Print server.
• Power saving mode (not needed)
• FreeNAS
• Install R.

Compare to other NAS

• Synology DS712+ Diskless System Network Storage. The Synology's wiki page here.
• D-LINK DNS 320L 800 MHz Marvell 88F6281 (Kirkwood), 128 MB. http://dns323.kood.org/dns-320
• ReadyNAS from Netgear
• Western Digital My Book Live Duo 4TB 800MHz PowerPC CPU and 256MB of memory.
• ZyXEL NSA320 and NSA310 Diskless

NAS hard disks

• Western Digital Red 2 TB NAS