Router: Difference between revisions
No edit summary |
|||
| Line 1: | Line 1: | ||
= DD-WRT = | |||
* Install it on [https://wiki.dd-wrt.com/wiki/index.php/Linksys_WRT54GL wrt54gl router] (v3.0-r44715 '''std''' 11/03/20). [https://downloads.linksys.com/downloads/userguide/WRT54GL_V11_UG_C-Web.pdf Manual] of Wrt54gl from linksys.com. | |||
* If I forget the admin username/password, I need to hold the reset button and apply power for 30 seconds. It will ask me to reset the adminstrator username/password. | |||
Web Interface </BR> | |||
* Setup | |||
** Network Setup. Default is 192.168.1.1. I changed it to 192.168.10.1 | |||
** DDNS | |||
** MAC Address Clone | |||
** Advanced Routing | |||
** Switch Config | |||
** Networking | |||
** Tunnels | |||
* Wireless | |||
** Basic Settings: Default SSID: '''dd-wrt'''. Wireless mode (2.4 GHz): AP, Client, Client Bridge, Adhoc, Repeat, Repeat Bridge | |||
** Radius | |||
** Wireless Security | |||
** MAC Filter | |||
** Advanced Settings | |||
** WDS | |||
* Services | |||
** Services | |||
** VPN | |||
** Hotspot | |||
* Security | |||
** Firewall | |||
** VPN Passthrough | |||
* Access Restrictions | |||
** WAN Access | |||
* NAT/QoS | |||
** Port Forwarding | |||
** Port Range Forwarding | |||
** Port Triggering | |||
** UPnP | |||
** DMZ | |||
** QoS | |||
* Administration | |||
** Management | |||
** Keep Alive | |||
** Commands | |||
** WOL | |||
** Factory Defaults | |||
** Firmware Upgrade | |||
** Backup | |||
* Status | |||
** Router | |||
** WAN | |||
** LAN | |||
** Wirelss | |||
** Bandwidth | |||
** Syslog | |||
** Sys-Info | |||
= OpenWRT = | = OpenWRT = | ||
* See [[Dual_boot#Proxmox|Netboot]]. | * See [[Dual_boot#Proxmox|Netboot]]. | ||
Revision as of 13:17, 26 October 2025
DD-WRT
- Install it on wrt54gl router (v3.0-r44715 std 11/03/20). Manual of Wrt54gl from linksys.com.
- If I forget the admin username/password, I need to hold the reset button and apply power for 30 seconds. It will ask me to reset the adminstrator username/password.
Web Interface
- Setup
- Network Setup. Default is 192.168.1.1. I changed it to 192.168.10.1
- DDNS
- MAC Address Clone
- Advanced Routing
- Switch Config
- Networking
- Tunnels
- Wireless
- Basic Settings: Default SSID: dd-wrt. Wireless mode (2.4 GHz): AP, Client, Client Bridge, Adhoc, Repeat, Repeat Bridge
- Radius
- Wireless Security
- MAC Filter
- Advanced Settings
- WDS
- Services
- Services
- VPN
- Hotspot
- Security
- Firewall
- VPN Passthrough
- Access Restrictions
- WAN Access
- NAT/QoS
- Port Forwarding
- Port Range Forwarding
- Port Triggering
- UPnP
- DMZ
- QoS
- Administration
- Management
- Keep Alive
- Commands
- WOL
- Factory Defaults
- Firmware Upgrade
- Backup
- Status
- Router
- WAN
- LAN
- Wirelss
- Bandwidth
- Syslog
- Sys-Info
OpenWRT
- See Netboot.
- Table of Hardware: Ideal for OpenWrt + Wifi6 (802.11ax) supported
- GL.iNet GL-MT3000
- OpenWrt One WiFi 6 router samples are now available for $89
GL.iNet GL-MT3000 (Beryl AX)
- User Guide
- GL-MT3000: Upgrade to latest OpenWRT
- OpenWrt page for GL.iNet GL-MT3000
- Amazon
- Travel Smarter with a Travel Router
OPNSense
- OPNSense - a powerful, open source, network firewall and router 4/19/2022
- Building a Business - Ep. 2: Installing OPNSense or pfSense as our Firewall and Router. 9/4/2022
- *Building a Business - Ep 3 - VLAN Setup in pfSense and OPNSense four our segmented network 9/11/2022
- How to build your own router and firewall with Opnsense 12/27/2024