Udoo

Documentation

• Starting manual
• Mechanical Specs
• Schematics
• Pinout explained

More Resource

Facebook

https://www.facebook.com/udooboard

Community

• Blog
• Forum

Download

• SD Image and instruction to burn the image to microSD card; like

sudo umount /dev/sdc5
sudo dd bs=4M if=~/Downloads/udoo_dual_ubuntu1204_v2.0.img of=/dev/sdc
sudo sync
df -h # find out <sd_label> in /media/<sd_label>
sudo umount /media/<sd_label>

• Arduino IDE for UDOO

Arduino Programming

http://www.elinux.org/UDOO_programming_the_embedded_Arduino_microcontroller

From Udoo itself

I can use dmesg | grep ttymxc3 to double check the device is attached.

Use sudo ln -sf /dev/ttymxc3 /dev/ttyS0 each time we boot the Ubuntu (or add it to the local.rc file to ensure it occurs on each boot) . See the forum discussion.

Simple LED sketch works well.

The Ethernet webServer sketch does not work. Why?

On an External computer

First I unplug J18 jumper, remove microSD card, and connect microUSB to CN6 in UDOO.

Download the official Arduino IDE 1.5.4.

I try to use dmesg | grep cp210x to check the device. The obstacle is the device is not found in Arduino IDE (No device found on ttyUSB0). If I try to follow 'Serial Driver' part to download and run 'make' , I will get an error

Linux_3.x.x_VCP_Driver_Source/cp210x.c:164:12: Error： 'usb_serial_probe' undeclared here (not in a function)
Linux_3.x.x_VCP_Driver_Source/cp210x.c:165:16: Error :  'usb_serial_disconnect' undeclared here (not in a function)

Serial port monitor

On Linux, I can use minicom program to monitor serial port. We can install it by using 'sudo apt-get install minicom'.

Use sudo minicom -s to configure minicom first. Make sure the serial port is correct. For example, use /dev/ttyS0 when we use UDOO and dev/ttyUSB0 when we use external PC. The baud rate is set to 9600 8N1 and that 'Hardware flow control' is set to 'no'. Once we are done with the settings, use 'Save setup as dfl' and minicom will start up with the correct settings next time.

We shall not launch minicom immediately. We shall let Arduino IDE to finish uploading a sketch and then we can launch minicom. We can quit minicom by using Ctrl+A and z and x. If we start minicom before Arduino IDE finishes uploading a sketch, Arduino IDE will not be able to upload successfully; it will show an error 'no device found on /dev/ttyS0'.

Misc

Install Ubuntu 12.04 or Android

• http://feilipu.me/2013/11/09/udoo-ubuntu-12-04-guide/
• http://www.elinux.org/UDOO_creating_a_bootable_Micro_SD_card_from_precompiled_image

sudo umount /dev/sdc1
sudo dd bs=1M if=/mnt/ssd/tmp/udoo_dual_android_v1.4.1.img of=/dev/sdc
sudo sync
sudo umount /media/<sd_label>

The following image shows the partitions in microSD card with Android OS.

Install Gapps in Android

• http://www.udoo.org/guide-how-to-install-gapps-on-udoo-running-android/

The real sdcX number can be found by using 'df -h' command.

sudo umount /dev/sdc* 
sudo unzip gapps-jb-20130812-signed.zip
sudo mkdir /mnt/sdc4
df -h # find /media/brb/data1 partition
sudo mount /dev/sdc4 /mnt/sdc4
cd gapps
sudo rsync -avu system/* /mnt/sdc4/

brb@brb-P45T-A:~/Downloads/gapps$ df -h
檔案系統        容量  已用  可用 已用% 掛載點
/dev/sda1       1.8T   57G  1.7T    4% /
none            4.0K     0  4.0K    0% /sys/fs/cgroup
udev            4.0G   12K  4.0G    1% /dev
tmpfs           810M  920K  809M    1% /run
none            5.0M     0  5.0M    0% /run/lock
none            4.0G   80K  4.0G    1% /run/shm
none            100M   12K  100M    1% /run/user
/dev/sdc4       5.2G   67M  4.9G    2% /media/brb/data1

brb@brb-P45T-A:~/Downloads/gapps$ ls /mnt/sdc4
anr       app-lib      dalvik-cache  drm         media     resource-cache  user
app       app-private  data          local       misc      ssh
app-asec  backup       dontpanic     lost+found  property  system

brb@brb-P45T-A:~/Downloads/gapps$ sudo rsync -avu system/* /media/sdc4/

brb@brb-P45T-A:~/Downloads/gapps$ ls /mnt/sdc4
addon.d   app-lib       data       framework   media           ssh     usr
anr       app-private   dontpanic  lib         misc            system
app       backup        drm        local       property        tts
app-asec  dalvik-cache  etc        lost+found  resource-cache  user
brb@brb-P45T-A:~/Downloads/gapps$ 

flash video

http://udoo.org/forum/viewtopic.php?f=17&t=137

sudo apt-get install gnash
sudo apt-get install browser-plugin-gnash
sudo apt-get install firefox
sudo apt-get install gnome-system-tools

Display Size

http://udoo.org/forum/viewtopic.php?f=6&t=119

VNC

http://udoo.org/forum/viewtopic.php?f=6&t=110

This tutorial teaches how to add tightvncserver to rc.local file so it is available on booting.

# Install tightvncserver
sudo apt-get install tightvncserver

sudo nano /etc/rc.local
# Add the following line before 'exit 0' line.
vncserver :1 -geometry 800x600 -depth 24

View Ubuntu 12.04 Desktop on Android (Galaxy tab 8.9) by using bVNC Free - Secure VNC Viewer app.

Look at the boot process via USB to serial interface

Check out this tutorial.

Speed comparison via C program

http://udoo.org/forum/viewtopic.php?f=2&t=470

Clonezilla image of Ubuntu 13.10 with ROS

http://udoo.org/forum/viewtopic.php?f=2&t=147&start=10

Node.js + GPIO

http://udoo.org/forum/viewtopic.php?f=8&t=391

http://udoo.org/forum/viewtopic.php?f=8&t=431 (Installation of Node.js)

Set up Qt

• http://udoo.org/forum/viewtopic.php?f=8&t=247 (OLD post)
• http://www.udoo.org/qt-3d-with-opengl-es-2-0/ (Working)

Change time zone

sudo dpkg-reconfigure tzdata
more /etc/timezone
# US/Eastern
sudo service cron stop
sudo service cron start