Motioneye

From 太極
Revision as of 15:48, 27 September 2019 by Brb (talk | contribs) (→‎motionEyeOS)
Jump to navigation Jump to search

Motion software

motionEye

motionEyeOS

My motionEyeOS settings

  • motionEye: 0.39.2
  • Motion: 4.1.1
  • Service: samba=Off
  • Expert settings: GPU=128
  • Video devices: 800x600, video rotation=180, frame rate=10 (Pi Zero W), 1600x1200, video rotation=0, frame rate=15->10 (Pi 2B). Note: changing the video frame rate will immediately change the streaming frame rate. So we need to remember to modify the streaming frame rate. Using frame rate=20 will make the video pixeled.
  • Text overlay: Left=disabled
  • Video streaming: streaming frame rate=2, streaming quality=85%, streaming resolution=50%, streaming port=8082.
  • Still images: off
  • Movies: H.264/OMX (.mp4), movie quality=75%, Motion trigger, maximum movie length=120 seconds, Preserve movies=1 week
  • Motion detection: frame rate threshold=1%, auto noise detection, light switch detection=75%, motion gap=10, capture before=5, capture after=5, minimum motion frame=5 (or go 20 by default), Mask=on, Show frame changes=on.
  • Working schedule: On.

Tips

  • Use a large capacity USB drive for storage (GParted formatted to ext4). It will be mounted to /data/media/sda1 in my case. So this is the path I need to enter for the 'Root Directory' under the 'File Storage' category.
  • For some reason, the external USB drive was not mounted but the data was still saved to microSD card. See this post USB drive not listed in File Storage dropdown. Unplug the USB drive and plug it in Ubuntu 18.04. Still cannot mount it with sudo mount -t ext4 /dev/sdb1 /mnt. The error message is "can't read superblock on /dev/sdb1". Use sudo fsck /dev/sdb1 command and it shows "Journal checksum error" (same error as I saw from dmesg.log log file in motioneyeos). It will ask to fix it. Answer "yes" a few times as needed and it will exit automatically. Now I can mount the USB drive in Ubuntu 18.04 and also have it recognized again in motioneyeos. In fact, fsck is available in motioneyeos too. It seems to be a good idea to run fsck periodically and send a message if something is wrong.
  • (5/6/2019) For some reason the images for some dates disappeared. In fact, the images are not lost after I fixed it on 5/10/2019.
  • (5/10/2019) I update motionEyeOS to the latest (20190427). However the samsung external USB drive can't be detected. mount command shows a superblock error. Plug the flash drive in Ubuntu and run "sudo fsck -yf /dev/sdd1". It shows an error. The error asks to get a new version of e2fsck. I follow the instruction here to do install the newest e2fsck. Run fsck again and something was fixed. Plug the drive into Raspi and the drive is recognized (df -h). 
    $ sudo fsck -yf /dev/sdd1
[sudo] password for brb: 
fsck from util-linux 2.27.1
e2fsck 1.42.13 (17-May-2015)
/dev/sdd1 has unsupported feature(s): metadata_csum
e2fsck: Get a newer version of e2fsck!

# Update e2fsck

$ e2fsck -V
e2fsck 1.44.5 (15-Dec-2018)
	Using EXT2FS Library version 1.44.5, 15-Dec-2018
$ sudo fsck -yf /dev/sdd1
fsck 1.44.5 (15-Dec-2018)
e2fsck 1.44.5 (15-Dec-2018)
samsung: recovering journal
JBD2: Invalid checksum recovering block 6 in log
Journal checksum error found in samsung
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information
Free blocks count wrong (27612652, counted=29793316).
Fix? yes

Free inodes count wrong (7836079, counted=7838321).
Fix? yes


samsung: ***** FILE SYSTEM WAS MODIFIED *****
  • Log files (motion.log, motioneye.log, messages.log, boot.log and dmesg.log) can be accessed directly from the web interface (under "Expert Settings"). All except <messages.log> can be found in /var/log directory. The <messages.log> is coming from <messages> file in /data/log.
  • We can backup and restore the current settings
  • "motion.conf"
  • Getting a reboot loop problem on my 16GB microSD. It may be caused by using up the storage.
  • The Backup configuration file is called "motioneye-config.tar.gz". When we restore, it will ask to browse the file from the local drive.
  • Run a command, Command line access
  • Running Commands At Regular Intervals (Cron Support)
  • Threshold and mask. Hard to set up the motion trigger. #695
  • Table of actually frame rate depending on the resolution and target frame rate from my experiment (HW: Pi2):
resolution target fr 15 target fr 30
1600x1200 8.6
1280x1024 8.6
1280x720 11.65
1024x768 13 15
800x600 15 23.5

False positive

How to deal with tree leaves shadow moves with wind (don't want to use 'Edit Mask')

MotionSetting.png

df -h

I plug in a 128GB USB drive. 

[root@meye-43815721 ~]# df -h
Filesystem                Size      Used Available Use% Mounted on
/dev/root               193.7M    173.7M      5.9M  97% /
devtmpfs                369.9M         0    369.9M   0% /dev
tmpfs                   374.4M     16.0K    374.4M   0% /dev/shm
tmpfs                   374.4M      2.3M    372.1M   1% /tmp
/dev/mmcblk0p1           29.9M     13.9M     16.0M  46% /boot
/dev/mmcblk0p3           13.6G    151.9M     12.7G   1% /data
/dev/mmcblk0p3           13.6G    151.9M     12.7G   1% /home/ftp/sdcard
/dev/mmcblk0p3           13.6G    151.9M     12.7G   1% /home/ftp/storage
/dev/sda1               117.2G     11.8G     99.3G  11% /data/media/sda1
/dev/sda1               117.2G     11.8G     99.3G  11% /home/ftp/storage/sda1
Retrieved from "https://wiki.taichimd.us/index.php?title=Motioneye&oldid=22253"