Raspberry: Difference between revisions

From 太極
Jump to navigation Jump to search
Line 84: Line 84:


== WebIOPi ==
== WebIOPi ==
WebIOPi is a REST framework and a webapp which allows you to control Raspberry Pi's GPIO.  
WebIOPi is a REST framework and a webapp which allows you to control Raspberry Pi's GPIO. It does not require apache to be installed.


* https://code.google.com/p/webiopi/wiki/README
* https://code.google.com/p/webiopi/wiki/README

Revision as of 13:59, 22 March 2013

Raspberry Pi

ARM architecture

http://www.memetic.org/raspbian-benchmarking-armel-vs-armhf/

Miscellaneous

Remote desktop connection with tightvnc

http://www.howtogeek.com/141157/how-to-configure-your-raspberry-pi-for-remote-shell-desktop-and-file-transfer/2/

tightvncserver
vncserver :1 -geometry 1600×900 -depth 16 -pixelformat rgb565:
vncserver –kill :1

Raspbian package repository

http://archive.raspbian.org/raspbian/pool/main/r/r-base/

Get internet by sharing the internet from another machine

  • https://wiki.archlinux.org/index.php/Internet_Share
  • static iP. Set up host eth0 IP and then set up RPi IP:
    • In Windows, allow Internet sharing. An IP of 192.168.0.2 will be automatically assigned to the Laptop's network card. Make static IP of 192.168.0.2 in Rasp Pi. Enter subnet mask and gateway (192.168.0.1). Also make an entry in /etc/resolv.conf with nameserver=192.168.0.1. Reboot and Rasp Pi will get Net all right.
    • In Linux, An IP of 10.42.0.37 will be assigned to eth0 card. Make static IP of 10.42.0.37 in Rasp Pi. Enter subset mask and gateway (10.42.0.1). Also make an entry in /etc/resolv.conf with nameserver=10.42.0.1. Reboot and Rasp Pi will get Net all right.
    • Other thoughts:
sudo nano /etc/network/interfaces

iface eth0 inet static
address 192.168.100.1
netmask 255.255.255.0
network 192.168.100.0
broadcast 192.168.100.255
gateway 192.168.100.254

The gateway is important and in most cases will always point to your firewalls, switch or routers IP address.

In my current setting, the host machine's eth0 has IP 10.42.0.1 (inet addr). The RPi has IP 10.42.0.37 and gateway 10.42.0.1.

$ netstat -rn
Kernel IP routing table
Destination     Gateway         Genmask         Flags   MSS Window  irtt Iface
0.0.0.0         192.168.1.1     0.0.0.0         UG        0 0          0 wlan0
10.42.0.0       0.0.0.0         255.255.255.0   U         0 0          0 eth0
169.254.0.0     0.0.0.0         255.255.0.0     U         0 0          0 wlan0
192.168.1.0     0.0.0.0         255.255.255.0   U         0 0          0 wlan0

And /etc/resolv.conf may be worth to be changed too. /etc/hostname and /etc/hosts are unnecessary.

An example of /etc/resolv.conf (set up linux DNS) shown from my RPi is

nameserver 10.42.0.1

But maybe another choice is nameserver 8.8.8.8.

Some tools for discovering the IPs in a network include Fing (iOS/Android) or Scapy (python).

IP scan tools

  • fing (ios, android, linux, windows). Command line usage
sudo fing -n 192.168.1.1/24

where /24 means 'network prefix' size 24 bits. Check wikipedia classless inter domain routing. For example, CIDR notation 192.168.100.0/24 would be equivalent to 192.168.100.0/255.255.255.0.

  • Angry ip scanner cross platform. open source. Basic knowledge on internet protocol. However, it is slow and show all instead of found ip's.
  • netbios. It does not discover linux boxes, however.

GPIO experiments

WebIOPi

WebIOPi is a REST framework and a webapp which allows you to control Raspberry Pi's GPIO. It does not require apache to be installed.

Run Python using webiopi module

sudo python -m webiopi 8000

Start/stop the background service

sudo /etc/init.d/webiopi start
sudo /etc/init.d/webiopi end

Start webiopi at startup:

sudo update-rc.d webiopi defaults

Note that we shall browse to http://localhost:8000/ instead of http://localhost:8000/webiopi. If something is still wrong, use a different port. The default user is "webiopi" and password is "raspberry".

It seems the code is still not stable. I kept getting a message "Error response" Error code 404. Message: Not Found. Error code explanation: 404 = Nothing matches the given URI.

Blink a single LED

I follow the instruction in https://projects.drogon.net/raspberry-pi/gpio-examples/tux-crossing/gpio-examples-1-a-single-led/ to install gpio program/library in raspberry pi. Here is the result

  • without PI cobbler: http://www.youtube.com/watch?v=xWJZRK4W13Q
  • with PI cobbler: see the picture below. The soldering part is not easy for a beginner. Be sure to follow some instruction on youtube videos to begin with. Note that the white stripe is on the edge closest to the SD card.

SingleLED.jpg

16x2 LCD

http://learn.adafruit.com/drive-a-16x2-lcd-directly-with-a-raspberry-pi. The '16x2' LCD means it can show 16 characters per row and there are 2 rows in total. Each character consists of 8x5 (height x width) dots.

RpyLCD.jpg